|
The mechanical layout was very similar to the berlinetta model, but the Pininfarina body clothing it was completely different. Also whilst the Pininfarina designed berlinetta body was constructed at the
Scaglietti in Modena, that of the spider was constructed at the Pininfarina works in Turin, before being delivered fully trimmed to the Ferrari factory for fitment of the mechanical components.
The 275 GTS had softer
more conservative lines than its berlinetta cousin, with echoes of the 250 GT California nose, featuring a shallow, almost rectangular, recessed egg crate grille, a full width bumper with plain overriders, and open headlights
in shallow recesses. The front wing line then ran back in virtually a straight line into the cabin section, before rising slightly into the rear wings that then fell into the rounded tail panel with horizontal wrap-around light
units, and quarter bumpers with rubber faced overriders. When the 330 GT 2+2 was restyled in 1965 it received a virtually identical nose treatment, and concurrently both the 275 GTS and 330 GT 2+2 had their eleven louvre front
wing exhaust air vents replaced by a triple louvre design, with a slim polished aluminium trim to the forward, top and bottom edges. The folding hood sat in a recess at the rear of the cabin when lowered, and was fitted with a
clip-on cover in this position.
The bodies were mounted on the same 2400mm wheelbase chassis as the 275 GTB with factory reference numbers 563, all were numbered in the odd chassis number road car sequence, and as with
the 275 GTB, it were available in right or left hand drive form. The standard wheels were Borrani wire wheels throughout the production period. A hardtop became available as an option during the production run, but was rarely
provided, so is something of a rarity today. Very early cars in the series were fitted with a "twin" passenger seat, basically a very wide seat to accommodate two people, although this idea was soon dropped in favour
of a standard two seat arrangement.
The engine was the same as that fitted to the 275 GTB, a single overhead camshaft per bank V12 unit, with factory type reference 213, of 3286cc capacity, with a bore and stroke of 77mm
x 58.8mm. It was fitted with a bank of either three twin choke Weber 40 DCZ/6 or 40 DFI/1 carburettors, with a twin coil and rear of engine mounted distributor ignition system, to produce a claimed 260 bhp, some 20 bhp below
that claimed for the berlinetta, confirming that this model was more restrained than its berlinetta peer. Similarly it shared the same transmission and suspension layout as the berlinetta, a five speed transaxle and four wheel
independent suspension, although it never received the final rigid torque tube transmission arrangement. The production period ran from late 1964 through to early 1966, in the chassis number range 06315 to 08653.
Engine
- Type : front, longitudinal 60° V12
- Bore/stroke : 77 x 58.8 mm
- Unitary displacement : 273.81 cc
- Total displacement : 3285.72 cc
- Compression ratio : 9.2 : 1
- Maximum power : 191 kW (260 hp) at 7000 rpm
- Power per litre : 79 hp/l
- Valve actuation : single overhead camshaft per bank, two valves per cylinder
- Fuel feed : three Weber 40 DCZ/6 or 40 DFI/1 carburettors
- Ignition : single spark plug per cylinder, two coils
- Lubrication : wet sump
- Clutch : single-plate
Chassis
- Frame : tubular steel
- Suspension
: Front suspension: independent, unequal-length wishbones, coil springs over telescopic shock absorbers, anti-roll bar. Rear suspension: independent, unequal-length wishbones, coil springs over telescopic shock absorbers, anti-roll bar
- Brakes : discs
- Transmission : 5-speed + reverse
- Steering : worm and roller
- Fuel tank : capacity 84 litres
- Tyres : [Front tyres: 195 or 205 x 14][Rear tyres: 195 or 205 x 14]
Bodywork
- Type : two-seater spider
- Length : 4350 mm
- Width : 1675 mm
- Height : 1250 mm
- Wheelbase : 2400 mm
- Front track : 1377 mm
- Rear track : 1393 mm
- Weight : 1120 kg (dry)
Performance
|
